DTH drilling tool is a kind of drilling system which uses compressed air as motivation, makes drilling impact motivation parts down the hole, to control the piston reciprocating motion by the distribution device in the hammer, and then impacts the DTH bit in the front of the hammer to transit the impacting power to the bit. The DTH bit in the front of the hammer breaks the rock to drill hole.
At present, DTH drilling tool is widely used in underground mining, quarries, hydraulic and Hydro-Power Engineering, water well drilling, Mineral exploration, anchoring hole drilling, geothermal engineering, Subway excavation, another civil engineering. It has the advantage of high flatness, smooth hole wall, high rigidity of drill rod and hammer, independent of high axial thrust, no limit of drilling depth, low cost of devices and are easy to maintain. At the drilling hole of diameter 105mm-254mm, plenty of the DTH drilling tools are used.
Hammer inch | Bits diameter | Hammer inch | |
---|---|---|---|
height | weight | ||
1" | 64mm-70mm | 2 1/2"-2 3/4" | BR1 |
2" | 70mm-95mm | 2 3/4"-3 3/4" | MACH20/BR2 |
3" | 90mm-102mm | 3 1/2"-4" | COP32/COP34/MACH303 M30/DHD3.5/BR3 |
4" | 105mm-152mm | 4 1/8"-6" | COP44/DHD340/MACH44 SD4/M40/QL40 |
5" | 133mm-165mm | 5 1/4"-6 1/2" | COP54/DHD350R/MACH50 SD5/M50/QL50/BR5 |
6" | 152mm-254mm | 4 1/8"-10" | COP64/DHD360/SD6 M60/QL60/Bulroc BR6 |
8" | 203mm-330mm | 8"-13" | COP84/DHD380/SD8 QL80/M80 |
10" | 254mm-380mm | 10"-15" | SD10 NUMA100 |
12" | 305mm-508mm | 12"-20" | DHD1120/SD12 NUMA120/NUMA125 |
Hammers | Bit Shank | Connection Thread | Suitable bit | Working pressure | Air consumption | |
---|---|---|---|---|---|---|
2" | BR2 | RD50 box | ¢70-¢90mm | 0.7-1.75Mpa | 0.7Mpa | 4.5m3/min |
1.0Mpa | 4m3/min | |||||
1.4Mpa | 5m3/min | |||||
3" | DHD3.5 COP32/COP34 M30 | API 2 3/8"Reg | ¢90-¢110mm | 1.0-1.5Mpa | 1.0Mpa | 4.5m3/min |
1.5Mpa | 9m3/min | |||||
4" | DHD350, COP54, QL50, SD5, M50 | API 2 3/8"Reg/API 3 1/2"Reg | ¢135-¢155mm | 1.0-2.5Mpa | 1.0Mpa | 9m3/min |
1.8Mpa | 15m3/min | |||||
2.4Mpa | 23m3/min | |||||
5" | DHD340, COP44, QL40, SD4,M40 | API 2 3/8"Reg | ¢110-¢135mm | 1.0-2.5Mpa | 1.0Mpa | 6m3/min |
1.8Mpa | 10m3/min | |||||
2.4Mpa | 15m3/min | |||||
6" | DHD360, COP64, QL60, SD6, M60 | API 3 1/2"Reg | ¢155-¢190mm | 1.0-2.5Mpa | 1.0Mpa | 10m3/min |
1.8Mpa | 20m3/min | |||||
2.4Mpa | 28.5m3/min | |||||
8" | DHD380, COP84, QL80, SD8 | API 4 1/2"Reg | ¢195-¢254mm | 1.0-2.5Mpa | 1.0Mpa | 15m3/min |
1.8Mpa | 26m3/min | |||||
2.4Mpa | 34m3/min | |||||
10" | SD10, Numa100 | API 6 5/8"Reg | ¢254-¢311mm | 1.0-2.5Mpa | 1.0Mpa | 22m3/min |
1.8Mpa | 40m3/min | |||||
2.4Mpa | 55m3/min | |||||
12" | DHD1120, SD12, Numa120 | API 6 5/8"Reg | ¢305-¢445mm | 1.0-2.5Mpa | 1.0Mpa | 30m3/min |
1.8Mpa | 56m3/min | |||||
2.4Mpa | 78m3/min |
AITC always sources high quality DTH Drill pipes and adaptors that are carefully selected seamless steel pipe and high quality alloy steel for joint tools and are precisely friction welded to ensure straightness and concentricity. These have multiple precisely heat-treated tool joints. Internally and externally upset drill rods are available.
Outer diameter | Thread | Wall thickness | Length | |||
---|---|---|---|---|---|---|
MM | INCH | MM | MM | |||
76 | 3 |
API 2 3/8 REG, PI 2 7/8 REG, API 3 1/2 REG, API 4 1/2 REG , API 2 3/8 IF, API 2 7/8" IF, API 3 1/2" IF, API 4 1/2" IF, API 5 1/2" IF, BECO 3 1/2", |
6.3 8.0 |
1000-4000mm, 4000-6000mm |
||
89 | 3 1/2 | 6.3 8.8 |
1000-4000mm, 4000-6000mm |
|||
102 | 4 | 6.3 8.8 |
1500-4000mm, 4000-6000mm |
|||
114 | 4 1/2 | 7.5 8.0 10.0 |
1500-4500mm, 4500-9000mm |
|||
127 | 5 | 8.0 10.0 12.0 |
1500-4500mm, 4500-9000mm |
|||
133 | 5 1/4 | 8.0 10.0 12.0 |
1000-4000mm, 4000-12000mm |
|||
140 | 5 1/2 | 14.0 19.0 |
3000-9000mm, 9000-12000mm |
AITC always sources high quality DTH Drill pipes and adaptors that are carefully selected seamless steel pipe and high quality alloy steel for joint tools and are precisely friction welded to ensure straightness and concentricity. These have multiple precisely heat-treated tool joints. Internally and externally upset drill rods are available.
Eccentric Overburden Drilling System Consist of Guide device, Casing shoe, Reamer, Pilot bit, Guide sleeve and Locking kits.
Model | Casing sizes | Min. inner dia. of casing shoe | Reaming Dia. | Hammer shank | Drill pipe | |||
---|---|---|---|---|---|---|---|---|
Max. OD | Min. ID | Thread | O.D | Wrench Flat | ||||
ODEX90 | 115 | 102 | 90 | 123 | DHD3.5/COP32/QL30 | API 2 3/8" REG | 76 | 65 |
ODEX115 | 142 | 128 | 115 | 152 | DHD340/COP44/SD4/QL40/M40 | API 2 3/8" REG | 76 | 65 |
ODEX140 | 171 | 157 | 140 | 187 | DHD350R/COP54/SD5/QL50/M50 | API 2 3/8" REG | 89 | 65 |
ODEX165 | 196 | 183 | 165 | 211 | DHD360/COP64/SD6/QL60/M60 | API 2 3/8" REG | 114 | 95 |
ODEX190 | 222 | 205 | 190 | 237 | DHD360/COP64/SD6/QL60/M60 | API 3 1/2" REG | 114 | 95 |
ODEX240 | 273 | 261 | 240 | 308 | DHD380/COP84/SD8/QL80/M80 | API 3 1/2" REG | 114 | 95 |
ODEX280 | 324 | 305 | 280 | 378 | DHD1120/SD10/NUMA100 | API 4 1/2" REG | 114 | 95 |
Symmetric Drilling System is designed to drill and case a hole simultaneously through unstable ground conditions. The driver bit incorporated with a sacrificial ring or reusable ring makes a full face head design which significantly improves the penetration rate and hole straightness of drilling. The internal flushing grooves together with the built-in casing shoes gives a good seal to the bottom of the drilling hole, and thus minimizing the disruption of the surrounding of the drill hole. Following mentioned are a few features:
Symmetric Casing Drilling System consists of three parts: Polit bit, Casing shoe and Ring bit.
Casing Tube OD(mm | Casing Tube ID(mm) | Reamed Dia(mm) | Casing Shoe ID(mm) | Polit bit Dia(mm) | Hammer Type |
---|---|---|---|---|---|
108 | 93-99 | 118 | 86 | 77 | DHD3.5/QL30 |
114 | 102-104 | 127 | 91 | 82 | DHD3.5/QL30 |
127 | 115-117 | 136 | 101 | 92 | DHD3.5/QL30 |
140 | 124-128 | 152 | 117 | 105 | DHD340/SD4/QL40/M40 |
146 | 130-134 | 154 | 117 | 105 | DHD340/SD4/QL40/M40 |
168 | 148-156 | 185 | 140 | 125 | DHD350/SD5/QL50/M50 |
178 | 158-166 | 195 | 150 | 140 | DHD350/SD5/QL50/M50 |
183 | 163-171 | 193 | 154 | 144 | DHD350/SD5/QL50/M50 |
194 | 174-182 | 211 | 166 | 150 | DHD360/SD6/QL60/M60 |
219 | 199-207 | 237 | 193 | 165 | DHD360/SD6/QL60/M60 |
245 | 224-233 | 260 | 210 | 190 | DHD380/SD8/QL80/M80 |
273 | 253-257 | 308 | 241 | 220 | DHD380/SD8/QL80/M80 |
325 | 305-309 | 348 | 281 | 205 | SD10/NUMA100 |
406 | 382-388 | 440 | 364 | 340 | SD10/NUMA100 |
Concentric casing system with block is a revolutionary new bit design with wings that extend out larger in diameter than the casing while in the drilling position. The face design of the Bit keeps it almost identical with a conventional bit face, allowing for unmatched penetration rates and smooth operation while drilling through overburden, boulders, or bedrock. When drilling is completed, the bit is simply lifted off bottom, causing the wings to retract back into the guide body. This allows all tooling to be extracted while leaving the casing in place. There is no forward or reverse rotation required, nor any expensive rings left in the hole.
Concentric casing system with block consists of three parts: Guide Device and Block
Casing Tube OD(mm | Casing Tube ID(mm) | Reamed Dia(mm) | Casing Shoe ID(mm) | Hammer Type |
---|---|---|---|---|
186 | 149-155 | 184 | 140 | DHD350/SD5/QL50/MISSION50 |
178 | 159-165 | 194 | 150 | DHD350/SD5/QL50/MISSION50 |
193 | 173-180 | 206 | 164 | DHD360/SD6/QL60/MISSION60 |
219 | 199-206 | 234 | 182 | DHD360/SD6/QL60/MISSION50 |
244 | 224-260 | 260 | 210 | DHD380/SD8/QL80/MISSION80 |
273 | 251-257 | 305 | 240 | DHD380/SD8/QL80/MISSION80 |
323 | 301-310 | 348 | 284 | SD10/NUMA100 |
406 | 382-388 | 440 | 364 | SD10/NUMA100 |
457 | 433-439 | 488 | 413 | SD12/NUMA120/DHD1120 |
508 | 484-490 | 538 | 464 | SD12/NUMA120/DHD1120 |